 |
M480 BSP
V3.05.001
The Board Support Package for M480 Series
|
|
M480 BSP
V3.05.001
The Board Support Package for M480 Series
|
M480 series FMC driver source file. More...
Go to the source code of this file.
Functions | |
| void | FMC_Close (void) |
| Disable FMC ISP function. More... | |
| int32_t | FMC_ConfigXOM (uint32_t u32XomNum, uint32_t u32XomBase, uint8_t u8XomPage) |
| Config XOM Region. More... | |
| int32_t | FMC_Erase (uint32_t u32PageAddr) |
| Execute FMC_ISPCMD_PAGE_ERASE command to erase a flash page. The page size is 4096 bytes. More... | |
| int32_t | FMC_Erase_SPROM (void) |
| Execute FMC_ISPCMD_PAGE_ERASE command to erase SPROM. The page size is 4096 bytes. More... | |
| int32_t | FMC_Erase_Block (uint32_t u32BlockAddr) |
| Execute FMC_ISPCMD_BLOCK_ERASE command to erase a flash block. The block size is 4 pages. More... | |
| int32_t | FMC_Erase_Bank (uint32_t u32BankAddr) |
| Execute FMC_ISPCMD_BANK_ERASE command to erase a flash block. More... | |
| int32_t | FMC_EraseXOM (uint32_t u32XomNum) |
| Execute Erase XOM Region. More... | |
| int32_t | FMC_GetXOMState (uint32_t u32XomNum) |
| Check the XOM is actived or not. More... | |
| int32_t | FMC_GetBootSource (void) |
| Get the current boot source. More... | |
| void | FMC_Open (void) |
| Enable FMC ISP function. More... | |
| uint32_t | FMC_Read (uint32_t u32Addr) |
| Execute FMC_ISPCMD_READ command to read a word from flash. More... | |
| int32_t | FMC_Read_64 (uint32_t u32addr, uint32_t *u32data0, uint32_t *u32data1) |
| Execute FMC_ISPCMD_READ_64 command to read a double-word from flash. More... | |
| uint32_t | FMC_ReadDataFlashBaseAddr (void) |
| Get the base address of Data Flash if enabled. More... | |
| void | FMC_SetBootSource (int32_t i32BootSrc) |
| Set boot source from LDROM or APROM after next software reset. More... | |
| void | FMC_Write (uint32_t u32Addr, uint32_t u32Data) |
| Execute ISP FMC_ISPCMD_PROGRAM to program a word to flash. More... | |
| int32_t | FMC_Write8Bytes (uint32_t u32addr, uint32_t u32data0, uint32_t u32data1) |
| Execute ISP FMC_ISPCMD_PROGRAM_64 to program a double-word to flash. More... | |
| int32_t | FMC_WriteMultiple (uint32_t u32Addr, uint32_t pu32Buf[], uint32_t u32Len) |
| Program Multi-Word data into specified address of flash. More... | |
| int32_t | FMC_Write_OTP (uint32_t otp_num, uint32_t low_word, uint32_t high_word) |
| Program a 64-bits data to the specified OTP. More... | |
| int32_t | FMC_Read_OTP (uint32_t otp_num, uint32_t *low_word, uint32_t *high_word) |
| Read the 64-bits data from the specified OTP. More... | |
| int32_t | FMC_Lock_OTP (uint32_t otp_num) |
| Lock the specified OTP. More... | |
| int32_t | FMC_Is_OTP_Locked (uint32_t otp_num) |
| Check the OTP is locked or not. More... | |
| int32_t | FMC_ReadConfig (uint32_t u32Config[], uint32_t u32Count) |
| Execute FMC_ISPCMD_READ command to read User Configuration. More... | |
| int32_t | FMC_WriteConfig (uint32_t u32Config[], uint32_t u32Count) |
| Execute ISP commands to erase then write User Configuration. More... | |
| uint32_t | FMC_GetChkSum (uint32_t u32addr, uint32_t u32count) |
| Run CRC32 checksum calculation and get result. More... | |
| uint32_t | FMC_CheckAllOne (uint32_t u32addr, uint32_t u32count) |
| Run flash all one verification and get result. More... | |
| int32_t | FMC_SetSPKey (uint32_t key[3], uint32_t kpmax, uint32_t kemax, const int32_t lock_CONFIG, const int32_t lock_SPROM) |
| Setup security key. More... | |
| int32_t | FMC_CompareSPKey (uint32_t key[3]) |
| Execute security key comparison. More... | |
M480 series FMC driver source file.
Definition in file fmc.c.
1.8.15